View NL8060BC26-30D_6945683.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

document number: dod-pp-0394 (3rd edition) published date: october 2007 cp(n) ? nec lcd technologies, ltd. 2007, all rights reserved. 1 this preliminary data sheet is updated document from dod-pp-0383(2). all information is subject to change without notice. please confirm the sales representative before starting to design your system. tft color lcd module NL8060BC26-30D 26cm (10.4 type) svga lvds interface (1port) preliminary data sheet dod-pp-0394 (3rd edition) www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 2 introduction the copyright to this document belongs to nec lcd technologies, ltd. (hereinafter called "nec"). no part of this document will be used, reproduced or copied without prior written consent of nec. nec does and will not assume any liability for infringement of patents, copyrights or other intellectual property rights of any third party arising out of or in connection with application of the products described herein except for that directly attributable to mechanisms and workmanship thereof. no license, express or implied, is granted under any patent, c opyright or other intellectual property right of nec. some electronic parts/components would fail or malfunction at a certain rate. in spite of every effort to enhance reliability of products by nec, the possibility of failures and malfunction might not be avoided entirely. to prevent the risks of damage to death, human bodily injury or other property arising out thereof or in connection therewith, ea ch customer is required to take sufficient measures in its safety designs and plans including, but not limited to, redundant system, fire-containment and anti-failure. the products are classified into three quality grades: "standard" , "special" , and "specific" of the highest grade of a quality assurance program at the choice of a customer. each quality grade is designed for applications described below. any customer who intends to use a product for application other than that of standard quality grade is required to contact an nec sales representative in advance. the standard quality grade applies to the products developed, designed and manufactured in accordance with the nec standard quality assurance pr ogram, which are designed for such application as any failure or malfunction of the pr oducts (sets) or parts/components incorporated therein a customer uses are, directly or indirectly , free of any damage to death, human bodily injury or other property, like general electronic devices. examples: computers, office automation equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment, industrial robots, etc. the special quality grade applies to the products developed, designed and manufactured in accordance with an nec quality assurance program stricter than the standard one, which are designed for such application as any failure or malfunction of the produc ts (sets) or parts/components incorporated therein a customer uses might directly cause any damage to death, human bodily injury or other property, or such application under more severe condition than that defined in the standard quality grade without such direct damage. examples: control systems for transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, medical equipment not specifically designed for life support, safety equipment, etc. the specific quality grade applies to the products developed, designed and manufactured in accordance with the standards or quality assurance program designated by a customer who requires an extremely higher level of reliability and quality for such products. examples: military systems, aircraft control equipment, aerospace equipment, nuclear reactor control systems, medical equipment/devices /systems for life support, etc. the quality grade of this product is the "standard" unless otherwise specified in this document. www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 3 contents introduction ................................................................................................................... ..................... 2 1. outline..................................................................................................................... ............................. 5 1.1 structure and principle .................................................................................................... .... 5 1.2 applic ation ................................................................................................................ .................... 5 1.3 feat ures ................................................................................................................... ....................... 5 2. general sp ecificat ions...................................................................................................... ........ 6 3. block diag ram ............................................................................................................... .................. 7 4. detailed sp ecificat ions..................................................................................................... ........ 8 4.1 mechanical spe cifications .................................................................................................. . 8 4.2 absolute m aximum ra tings.................................................................................................. 8 4.3 electrical c haracteristics................................................................................................. 9 4.3.1 lcd panel signal processing board ........................................................................................ ..... 9 4.3.2 backlight lamp........................................................................................................... ................ 10 4.3.3 power supply voltage ripple.............................................................................................. ......... 11 4.3.4 fuse..................................................................................................................... ....................... 11 4.4 power supply vo ltage sequence ..................................................................................... 12 4.4.1 lcd panel signal processing board ........................................................................................ ... 12 4.4.2 inverter (option) ........................................................................................................ ................ 12 4.5 connections and functi ons for inter face pins ...................................................... 13 4.5.1 lcd panel signal processing board ........................................................................................ ... 13 4.5.2 backlight lamp........................................................................................................... ................ 14 4.5.3 positions of plug and socket ............................................................................................. ......... 14 4.5.4 connection between receiver and transmitter for lvds ........................................................... 15 4.5.5 input data mapping ....................................................................................................... ............. 18 4.6 display colors and input data signals....................................................................... 20 4.6.1 combinations between input data signals, frc signal and msl signal ................................... 20 4.6.2 16,777,216 colors........................................................................................................ ............... 21 4.6.3 262,144 colors........................................................................................................... ................. 22 4.7 display positi ons .......................................................................................................... ............ 23 4.8 scanning di rections ........................................................................................................ ....... 23 4.9 input si gnal ti mings ....................................................................................................... ........ 24 4.9.1 outline of in put signal timings .......................................................................................... ........ 24 4.9.2 timing characteristics................................................................................................... ............. 25 4.9.3 input signal timing chart ................................................................................................ ............ 26 4.10 optics.................................................................................................................... ......................... 27 4.10.1 optical characteristics................................................................................................. ............. 27 4.10.2 definition of contrast ratio............................................................................................ ........... 28 4.10.3 definition of luminance uniformity ...................................................................................... ... 28 4.10.4 definition of response times ............................................................................................ ........ 28 4.10.5 definition of viewing angles............................................................................................ ........ 28 www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 4 contents 5. reliability tests ........................................................................................................... ............... 29 6. pre cautio ns ................................................................................................................. .................... 30 6.1 meaning of c aution signs ................................................................................................... . 30 6.2 caut ions ................................................................................................................... ..................... 30 6.3 atten tions................................................................................................................. ................... 30 6.3.1 handling of the product .................................................................................................. ........... 30 6.3.2 environment.............................................................................................................. ................. 31 6.3.3 characteristics.......................................................................................................... .................. 31 6.3.4 other .................................................................................................................... ...................... 32 7. outline drawin gs............................................................................................................ ............. 33 7.1 front view................................................................................................................. ................... 33 7.2 rear view .................................................................................................................. .................... 34 revision history ............................................................................................................... ................ 35 www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 5 1. outline 1.1 structure and principle color lcd module NL8060BC26-30D is composed of the amorphous silicon thin film transistor liquid crystal display (a-si tft lcd) panel structure with driver lsis for driving the tft (thin film transistor) array and a backlight. the a-si tft lcd panel structure is injected liquid crystal material into a narrow gap between the tft array glass substrate and a color-filter glass substrate. color (red, green, blue) data signals from a host system (e.g. signal generator, etc.) are modulated into best form for active matrix system by a signal processing circuit, and sent to the driver lsis which drive the individual tft arrays. the tft array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. color images are created by regulating the amount of transmitted light through the tft array of red, green and blue dots. 1.2 application ? for industrial use 1.3 features ? high luminance ? high contrast ? wide temperature range ? lvds interface ? reversible-scan direction ? selectable 8bit or 6bit digital signals for data of rgb ? edge light type (without inverter) ? replaceable lamp for backlight www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 6 2. general specifications display area 211.2 (h) 158.4 (v) mm diagonal size of display 26cm (10.4 inches) drive system a-si tft active matrix display color 16,777,216 colors (at 8-bit input, frc terminal= high) 262,144 colors (at 6-bit input, frc terminal= low or open) pixel 800 (h) 600 (v)pixels pixel arrangement rgb (red dot, green dot, blue dot) vertical stripe dot pitch 0.088 (h) 0.264 (v) mm pixel pitch 0.264 (h) 0.264 (v) mm module size 243.0 (w) 185.1 (h) 10.5 (d) mm (typ.) weight (475) g (typ.) contrast ratio (600:1) (typ.) viewing angle at the contrast ratio 10:1 ? horizontal: right side 80 (typ.), left side 80 (typ.) ? vertical: up side 80 (typ.), down side 80 (typ.) designed viewing direction at dps terminal= low or open: normal scan ? viewing direction without image reversal: up side (12 o'clock) ? viewing direction with contrast peak: down side (6 o'clock) ? viewing angle with optimum grayscale: normal axis (perpendicular) polarizer surface antiglare polarizer pencil-hardness 3h (min.) [by jis k5400] color gamut at lcd panel center 40% (typ.) [against ntsc color space] response time ton+toff (10% 90%) (25)ms (typ.) luminance at ibl=5.0marms / lamp 400cd/m 2 (typ.) signal system lvds 1port (receiver: equivalent of thc63lvdf84b, thine electronics inc.) [8-bit digital signals for data of rgb colors, dot clock (clk), data enable (de)] power supply voltage lcd panel signal processing board: 3.3v backlight edge light type: 2 cold cathode fluorescent lamps (without inverter) replaceable part ? lamp holder set: type no. tbd recommended inverter (option) ? inverter: type no. 104pw201 power consumption at ibl= 5.0marms / lamp, checkered flag pattern tbd w (typ., power dissipation of the inverter is not included.) 3 3 www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 7 3. block diagram note1: relations between gnd (signal ground), fg (frame ground) and vblc (lamp low voltage terminal) in the product are as follows. gnd-fg connected gnd-vblc not connected fg-vblc not connected note2: gnd, fg and gndb must be connected to cu stomer equipment?s ground, and it is recommended that these grounds are connected together in customer equipment. note1 note2 lcd panel signal processing board host 2,400 lines lcd panel h: 800 3 (r, g, b) v: 600 600 lines vcc gnd dc/dc converter lcd module (product) fuse h-driver fg d0+ d0- d1+ d1- d2+ d2- d3+ d3- 100 100 100 100 dps clk+ clk- 100 frc note1 note2 v-driver power supply for gradation inverter (option) vblh gndb vblc note2 2 lamps backlight (edge light type) note1 vblh vddb 50k 47k 50k controller with receiver for lvds msl www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 8 4. detailed specifications 4.1 mechanical specifications parameter specification unit module size 243.0 0.5 (w) 185.1 0.5 (h) 10.5 0.5 (d) note1 mm display area 211.2 (h) 158.4 (v) note1 mm weight (475) (typ.), tbd (max.) g note1: see " 7. outline drawings ". 4.2 absolute maximum ratings parameter symbol rating unit remarks lcd panel signal processing board vcc -0.3 to +4.0 v power supply voltage lamp voltage vblh 2,000 vrms display signals note1 vd input voltage for signals function signals note2 vf -0.3 to vcc+0.3 v - storage temperature tst -30 to +80 c - front surface topf -20 to +70 c note3 operating temperature rear surface topr -20 to +70 c note4 95 % ta 40 c 85 % 40 < ta 50 c 55 % 50 < ta 60 c relative humidity note5 rh 36 % 60 < ta 70 c absolute humidity note5 ah 70 note6 g/m 3 ta > 70 c note1: d0+/-, d1+/-, d2+/-, d3+/-, clk+/- note2: dps, frc, msl note3: measured at center of lc d panel surface (including self-heat) note4: measured at center of lcd module's rear shield surface (including self-heat) note5: no condensation note6: water amount at ta= 70c and rh= 36% 3 www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 9 4.3 electrical characteristics 4.3.1 lcd panel signal processing board (ta= 25 c) parameter symbol min. typ. max. unit remarks power supply voltage vcc 3.0 3.3 3.6 v - power supply current icc - tbd note1 tbd note2 ma at vcc= 3.3v permissible ripple voltage vrp - - 100 mvp-p for vcc high vth - - +100 mv differential input threshold voltage low vtl -100 - - mv at vcm= 1.2v note3 terminating resistance rt - 100 - - high vfh 0.7vcc - vcc v input voltage for dps, frc and msl signal low vfl 0 - 0.3vcc v high ifh - - 300 a input current for frc and msl signal low ifl -300 - - a cmos level note1: checkered flag pattern [by eiaj ed-2522] note2: pattern fo r maximum current note3: common mode voltage for lvds receiver www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 10 4.3.2 backlight lamp (ta= 25 c, note1) parameter symbol min. typ. max. unit remarks lamp current ibl 2.0 5.0 5.5 marms at ibl= 5.0marms: l= 400cd/m 2 (typ.) note3, note4 lamp voltage vblh - 520 - vrms note2, note3 850 - - vrms ta= 25 c note2, note3, note5, note8 lamp starting voltage vs 1,150 - - vrms ta= -20 c note2, note3, note5, note8 lamp oscillation frequency fo 50 - 72 khz note6 note1: this product consists of 2 backlight la mps, and these specifications are for each lamp. note2: the lamp voltage cycle between lamps should be kept on a same phase. "vs" and "vblh" are the voltage value between low voltage si de (cold) and high voltage side (hot). note3: the asymmetric ratio of working waveform for lamps (lamp voltage peak ratio, lamp current peak ratio and waveform space ratio) should be less than 5 % (see the following figure.). if the waveform is asymmetric, dc (d irect current) element apply into the lamp. in this case, a lamp lifetime may be shortened, because a distribution of a lamp enclosure substance inclines toward one side between lo w voltage terminal (cold terminal) and high voltage terminal (hot terminal). when designing the inverter, evaluate asymmetric of lamp working waveform sufficiently. pa: supply voltage/current peak for positive, pb: supply voltage/current peak for negative sa: waveform space for positive part, sb: waveform space for negative part note4: this product consists of 2 lamps. 2 lamps are contained in the 1 lamp holder, and both lamps are connected to 1 low voltage cable. recommended lamp current is 5.0marms typical for each lamp, and sum of 2 lamps is 10marms typical . the lamp current should be measured by high-frequency current meter at the low voltage terminal. note5: the inverter should be designed so that the lamp starting voltage can be maintained for more than 1 second. otherwise the lamp may not be turned on. note6: in case "fo" is not the recommended value, beat noise may display on the screen, because of interference between "fo" and "1/th". recommended value of "fo" is as following. th: horizontal signal period (see " 4.9.2 timing characteristics ".) n: natural number (1, 2, 3 ???????? ) note7: method of lamp cable installation may invite fluctuation of lamp current and voltage or asymmetric of lamp working waveform. when designing method of lamp cable installation, evaluate the fluctuation of lamp current, voltage and working waveform sufficiently. pa pb sa sb 0 ? pa - pb ? pb 100 5 % ? sa - sb ? sb 100 5 % fo = 1 4 1 th (2n-1) www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 11 note8: in case of inverter with ballast condenser, "vs" is the voltage level between ballast condenser and connector (refer to the below ?e xample of measurement?). "vs" should be designed to be more than minimum "vs". otherwise the lamp may not be turned on because the lamp starting voltage is less than minimum "vs". example of measurement probe capacity: 3pf (tektronix, inc.: p6015a) 4.3.3 power supply voltage ripple this product works, even if the ripple voltage leve ls are beyond the permissible values as following the table, but there might be noise on the display image. power supply voltage ripple voltage note1 (measure at input terminal of power supply) unit vcc 3.3v 100 mvp-p note1: the permissible ripple voltage includes spike noise. 4.3.4 fuse fuse parameter type supplier rating fusing current remarks tbd a vcc tbd tbd tbd v tbd a note1 note1: the power supply capacity should be more than the fusing current. if it is less than the fusing current, the fuse may not blow in a short time, and then nasty smell, smoke and so on may occur. transformer vs high voltage probe probe capacity inverter ballast condenser connector (lamp side) www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 12 4.4 power supply voltage sequence 4.4.1 lcd panel signal processing board * these signals should be measured at the terminal of 100 resistance. note1: in terms of voltage variation (voltage drop) while vcc rising edge is below 3.0v, a protection circuit may work, and then this product may not work. note2: display signals (d0+/-, d1+/-, d2+/-, d3 +/- and clk+/-) and func tion signals (dps, frc and msl) must be low or high impedance, exclude the valid period (see above sequence diagram), in order to avoid that internal circuit is damaged. if some of display and function signals of this product are cut while this product is working, even if the signal input to it once again, it might not work normally. vcc should be cut when the display and function signals are stopped. 4.4.2 inverter (option) note1: these are the display and function signals for lcd panel signal processing board. note2: the backlight should be turned on within the valid period of display and function signals, in order to avoid unstable data display. 0ms NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 13 4.5 connections and functions for interface pins 4.5.1 lcd panel signal processing board cn1 socket (lcd module side): fi-se20p-hfe (japan aviation electronics industry limited (jae)) adaptable plug: fi-s20s (japan aviation electronics industry limited (jae)) input data signal 8bit pin no. symbol signal map a map b input data signal 6bit remarks 1 d3+ or gnd pixel data or ground 2 d3- or gnd pixel data or ground r0-r1,g0-g1,b0-b1 r6-r7,g6-g7,b6-b7 ground note1 note3 note4 3 dps selection of scan direction high: reverse scan low or open: normal scan note2 4 frc selection of the number of colors high low or open note1 note5 5 gnd ground ground note4 6 clk+ 7 clk- pixel clock pixel clock note3 8 gnd ground ground note4 9 d2+ 10 d2- pixel data b4-b7,de b2-b5,de note3 11 gnd ground ground note4 12 d1+ 13 d1- pixel data g3-g7,b2-b3 g1-g5,b0-b1 note3 14 gnd ground ground note4 15 d0+ 16 d0- pixel data r2-r7,g2 r0-r5,g0 note3 17 gnd ground ground note4 18 msl selection of lvds input map low high low note5 19 vcc 20 vcc power supply power supply power supply note4 note1: see " 4.6 display colors and input data signals ". note2: see " 4.8 scanning directions ". note3: twist pair wires with 100 (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter. note4: all gnd and vcc terminals should be used without any non-connected lines. note5: see " 4.5.4 connection between receiver and transmitter for lvds ". www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 14 4.5.2 backlight lamp attention: vblh and vblc must be connected correctly. wrong connections will cause electric shock and also break down of the product. cn2 plug (lcd module side): bhr-04vs-1 (j.s.t mfg. co., ltd.) adaptable socket: sm03 (7-d1) b-bhs-1-tb(lf)(sn), sm03 (7-d1) b-bhs-1-tb (j.s.t mfg. co., ltd.) pin no. symbol signal remarks 1 vblh high voltage terminal (hot) cable color: pink 2 vblh high voltage terminal (hot) cable color: pink 3 n.c. - keep this pin open. 4 vblc low voltage terminal (cold) cable color: black 4.5.3 positions of plug and socket barcode label nameplate label rear side insert direction cn1 1 20 cn2 low voltage (cold) high voltage (hot) 4 2 1 high voltage caution marking disposal method marking for lamp www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 15 4.5.4 connection between receiver and transmitter for lvds (1) input data signal: 8bit, map a note1: recommended transmitter: thc63lvdm83r (thine electronics inc.) or equivalent note2: lsb (least significant bit) ? r0, g0, b0 msb (most significant bit) ? r7, g7, b7 note3: twist pair wires with 100 (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter. note4: input signals to tc4, tc5 and td6 are not used inside the product, but do not keep tc4, tc5 and td6 open to avoid noise problem. r2 r3 r4 r5 r6 r7 g2 g3 g4 g5 g6 g7 b2 b3 b4 b5 b6 b7 note4 note4 de r0 r1 g0 g1 b0 b1 note4 clk vcc gnd dps frc msl lvds transmitter thc63lvdm83r or equivalent note1 host d3+ d3- dps frc gnd clk+ clk- gnd d2+ d2- gnd d1+ d1- gnd d0+ d0- gnd msl vcc vcc ta0 ta1 ta2 ta3 ta4 ta5 ta6 tb0 tb1 tb2 tb3 tb4 tb5 tb6 tc0 tc1 tc2 tc3 tc4 tc5 tc6 td0 td1 td2 td3 td4 td5 td6 clk in td+ td- tclk+ tclk- tc+ tc- tb+ tb- ta+ ta- 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 gnd cn1 rd+ rd- rclk+ rclk- rc+ rc- rb+ rb- ra+ ra- gnd signal processor dps frc msl vcc note3 note2 lcd module (product) lcd controller receiver for lvds equivalent of thc63lvdf84b lcd panel signal processing board www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 16 (2) input data signal: 8bit, map b note1: recommended transmitter: thc63lvdm83r (thine electronics inc.) or equivalent note2: lsb (least significant bit) ? r0, g0, b0 msb (most significant bit) ? r7, g7, b7 note3: twist pair wires with 100 (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter. note4: input signals to tc4, tc5 and td6 are not used inside the product, but do not keep tc4, tc5 and td6 open to avoid noise problem. r0 r1 r2 r3 r4 r5 g0 g1 g2 g3 g4 g5 b0 b1 b2 b3 b4 b5 note4 note4 de r6 r7 g6 g7 b6 b7 note4 clk vcc gnd dps frc msl lvds transmitter thc63lvdm83r or equivalent note1 host d3+ d3- dps frc gnd clk+ clk- gnd d2+ d2- gnd d1+ d1- gnd d0+ d0- gnd msl vcc vcc ta0 ta1 ta2 ta3 ta4 ta5 ta6 tb0 tb1 tb2 tb3 tb4 tb5 tb6 tc0 tc1 tc2 tc3 tc4 tc5 tc6 td0 td1 td2 td3 td4 td5 td6 clk in td+ td- tclk+ tclk- tc+ tc- tb+ tb- ta+ ta- 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 gnd cn1 rd+ rd- rclk+ rclk- rc+ rc- rb+ rb- ra+ ra- gnd signal processor dps frc msl vcc note3 note2 lcd module (product) lcd controller receiver for lvds equivalent of thc63lvdf84b lcd panel signal processing board www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 17 (3) input data signal: 6bit note1: recommended transmitter thc63lvdm83r (thine electronics inc.) or equivalent note2: lsb (least significant bit) ? r0, g0, b0 msb (most significant bit) ? r5, g5, b5 note3: twist pair wires with 100 (characteristic impedance) should be used between lcd panel signal processing board and lvds transmitter. note4: input signals to tc4 and tc5 are not used inside the product, but do not keep tc4 and tc5 open to avoid noise problem. host gnd gnd dps frc gnd clk+ clk- gnd d2+ d2- gnd d1+ d1- gnd d0+ d0- gnd msl vcc vcc ta0 ta1 ta2 ta3 ta4 ta5 ta6 tb0 tb1 tb2 tb3 tb4 tb5 tb6 tc0 tc1 tc2 tc3 tc4 tc5 tc6 clk in tclk+ tclk- tc+ tc- tb+ tb- ta+ ta- 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 gnd cn1 rclk+ rclk- rc+ rc- rb+ rb- ra+ ra- gnd signal processor dps frc msl vcc note3 r0 r1 r2 r3 r4 r5 g0 g1 g2 g3 g4 g5 b0 b1 b2 b3 b4 b5 note4 note4 de clk vcc gnd dps frc msl note2 lcd module (product) receiver for lvds equivalent of thc63lvdf84b lcd controller lvds transmitter thc63lvdm83r or equivalent note1 lcd panel signal processing board www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 18 4.5.5 input data mapping (1) input data signal: 8bit , map a (2) input data signal: 8bit , map b r2 r3 r4 r5 r6 r7 g2 g3 g4 g5 g6 g7 b2 b3 clk+/- d0+/- d1+/- b4 b5 b6 b7 - de d2+/- - 1clk tc r0 r1 g0 g1 b0 d3+/- b1 r0 r1 r2 r3 r4 r5 g0 g1 g2 g3 g4 g5 b0 b1 clk+/- d0+/- d1+/- b2 b3 b4 b5 - de d2+/- - 1clk tc r6 r7 g6 g7 b6 d3+/- b7 www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 19 (3) input data signal: 6bit r0 r1 r2 r3 r4 r5 g0 g1 g2 g3 g4 g5 b0 b1 b2 b3 b4 b5 - de clk+/- d0+/- d1+/- d2+/- - 1clk tc www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 20 4.6 display colors and input data signals 4.6.1 combinations between input data signals, frc signal and msl signal this product can display in equivalent to 16,777,216 colors in 256 gray scales and 262,144 colors in 64 gray scales by combination between input data signals and frc signal. see following table. combination input data signals input data mapping cn1- pin no.1 and 2 frc terminal msl terminal display colors remarks 8 bit map a d3+/- high low 16,777,216 note1 8 bit map b d3+/- high high 16,777,216 note1 6 bit - gnd low or open low 262,144 note2 note1: see " 4.6.2 16,777,216 colors ". note2: see " 4.6.3 262,144 colors ". www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 21 4.6.2 16,777,216 colors this product can display equivalent of 16,777,216 colors in 256 gray scales by combination and . (see " 4.6.1 combinations between input data signals, frc signal and msl signal ".) also the relation between display colors and input data signals is as the following table. data signal (0: low level, 1: high level) display colors r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 basic colors black blue red magenta green cyan yellow white 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 red gray scale black dark bright red 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 : : 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green gray scale black dark bright green 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 : : 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue gray scale black dark bright blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 : : 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 22 4.6.3 262,144 colors this product can display equivalent of 262,144 colors in 64 gray scales by combination . (see " 4.6.1 combinations between input data signals, frc signal and msl signal ".) also the relation between display colors and input data signals is as the following table. data signal (0: low level, 1: high level) display colors r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 basic colors black blue red magenta green cyan yellow white 000000 000000 111111 111111 000000 000000 111111 111111 000000 000000 000000 000000 111111 111111 111111 111111 000000 111111 000000 111111 000000 111111 000000 111111 red gray scale black dark bright red 000000 000001 000010 : : 111101 111110 111111 000000 000000 000000 : : 000000 000000 000000 000000 000000 000000 : : 000000 000000 000000 green gray scale black dark bright green 000000 000000 000000 : : 000000 000000 000000 000000 000001 000010 : : 111101 111110 111111 000000 000000 000000 : : 000000 000000 000000 blue gray scale black dark bright blue 000000 000000 000000 : : 000000 000000 000000 000000 000000 000000 : : 000000 000000 000000 000000 000001 000010 : : 111101 111110 111111 www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 23 4.7 display positions the following table is the coordinates per pixel (see " 4.8 scanning directions ".). c (0, 0) r g b c( 0, 0) c( 1, 0) ? ? ? c( x, 0) ? ? ? c(798, 0) c(799, 0) c( 0, 1) c( 1, 1) ? ? ? c( x, 1) ? ? ? c(798, 1) c(799, 1) ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? c( 0, y) c( 1, y) ? ? ? c( x, y) ? ? ? c(798, y) c(799, y) ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? c( 0, 598) c( 1, 598) ? ? ? c( x, 598) ? ? ? c(798, 598) c(799, 598) c( 0, 599) c( 1, 599) ? ? ? c( x, 599) ? ? ? c(798, 599) c(799, 599) 4.8 scanning directions the following figures are seen from a front view . also the arrow shows the direction of scan. note1: meaning of c (x, y) and d (x, y) c (x, y): the coordinates of the display position (see " 4.7 display positions ".) d (x, y): the data number of input signal for lcd panel signal processing board figure 1. normal scan (dps: low or open) c (0, 0) d (0, 0) c (0, 599) d (0, 599) c (799, 599) d (799, 599 c (799, 0) d (799, 0) note1 figure 2. reverse scan (dps: high) note1 c (0, 0) d (799, 599) c (0, 599) d (799, 0) c (799, 599) d (0, 0) c (799, 0) d (0, 599) www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 24 4.9 input signal timings 4.9.1 outline of input signal timings ? horizontal signal note1 ? vertical signal note1 note1: this diagram indicates virtual signal for set up to timing. note2: see " 4.9.3 input signal timing chart " for numeration of pulse. display period horizontal display period (thd) de (data enable) vertical display period (tvd) 1 2 34 600 display period de (data enable) note2 www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 25 4.9.2 timing characteristics (note1, note2, note3) parameter symb ol min. typ. max. unit remarks frequency 1/tc 34.0 38.362 40.0 mhz 26.067ns (typ.) duty - - clk rise time, fall time - - ns - setup time - ns clk-data hold time - ns data rise time, fall time - - ns - 24.0 26.693 30.1 s cycle th - 1,024 - clk 37.463khz (typ.) horizontal display period thd 800 clk - 16.1 16.683 17.2 ms cycle tv - 625 - h vertical (one frame) display period tvd 600 h 59.94hz (typ.) setup time - ns clk-de hold time - ns de rise time, fall time - - ns - note1: definition of para meters is as follows. tc= 1clk, th= 1h note2: see the data sheet of lvds transmitter. note3: vertical cycle (tv) should be specified in integral multiple of horizontal cycle (th). www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 26 4.9.3 input signal timing chart horizontal timing vertical timing invalid 1 2 799 800 clk de data (r0-r7) (r0-r5) (g0-g7) or (g0-g5) (b0-b7) (b0-b5) invalid thd th de invalid invalid 1 2 599 600 tvd tv tc data (r0-r7) (r0-r5) (g0-g7) or (g0-g5) (b0-b7) (b0-b5) www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 27 4.10 optics 4.10.1 optical characteristics (note1, note2) parameter condition symbol min. typ. max. unit measuring instrument remarks luminance white at center r= 0 , l= 0 , u= 0 , d= 0 l tbd 400 - cd/ m 2 bm-5a - contrast ratio white/black at center r= 0 , l= 0 , u= 0 , d= 0 cr tbd (600) - - bm-5a note3 luminance uniformity white r= 0 , l= 0 , u= 0 , d= 0 lu - 1.25 1.4 - bm-5a note4 x coordinate wx 0.283 0.313 0.343 - white y coordinate wy 0.299 0.329 0.359 - x coordinate rx - tbd - - red y coordinate ry - tbd - - x coordinate gx - tbd - - green y coordinate gy - tbd - - x coordinate bx - tbd - - chromaticity blue y coordinate by - tbd - - color gamut r= 0 , l= 0 , u= 0 , d= 0 at center, against ntsc color space c 35 40 - % sr-3 note5 white to black ton - (6) tbd ms response time black to white toff - (19) tbd ms bm-5a note6 note7 right u= 0 , d= 0 , cr 10 r tbd 80 - left u= 0 , d= 0 , cr 10 l tbd 80 - up r= 0 , l= 0 , cr 10 u tbd 80 - viewing angle down r= 0 , l= 0 , cr 10 d tbd 80 - ez contrast note8 note1: these are initial characteristics. note2: measurement conditions are as follows. ta= 25 c, vcc= 3.3v, ibl= 5.0marms/lamp, display mode: svga, horizontal cycle= 1/37.463khz, vertical cycle= 1/59.94hz, dps= low or open: normal scan optical characteristics are measured at lumina nce saturation after 20minutes from working the product, in the dark room. also measurement methods are as follows. note3: see " 4.10.2 definition of contrast ratio ". note4: see " 4.10.3 definition of luminance uniformity ". note5: these coordinates are found on cie 1931 chromaticity diagram. note6: product surface temperature: topf= tbd c note7: see " 4.10.4 definition of response times ". note8: see " 4.10.5 definition of viewing angles ". lcd module (product) 50cm 1 photodetector (bm-5a or sr-3) photodetector (ez contrast) lcd module (product) 3 www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 28 4.10.2 definition of contrast ratio the contrast ratio is calculated by using the following formula. luminance of white screen luminance of black screen 4.10.3 definition of luminance uniformity the luminance uniformity is calculated by using following formula. maximum luminance from to minimum luminance from to the luminance is measured at n ear the 5 points shown below. 4.10.4 definition of response times response time is measured, the luminance changes from "white" to "black", or "black" to "white" on the same screen point, by photo-detector. ton is the time it takes the luminance change from 90% down to 10%. also toff is the time it takes the luminance change from 10% up to 90% (see the following diagram.). 4.10.5 definition of viewing angles contrast ratio (cr) = luminance uniformity (lu) = 133 400 667 100 300 500 left upper lower n ormal axis (perpendicular) u d r l 12 o?clock right 100% 90% 10% 0% ton toff luminance white black www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 29 5. reliability tests test item condition judgment high temperature and humidity (operation) 60 2 c, rh= 90%, 240hours display data is black. high temperature (operation) 70 3 c, 240hours display data is black. heat cycle (operation) -20 3 c 1hour 70 3 c 1hour 50cycles, 4 hours/cycle display data is black. thermal shock (non operation) -30 3 c 30minutes 80 3 c 30minutes 100cycles, 1hour/cycle temperature transition time is within 5 minutes. esd (operation) 150pf, 150 , 10kv 9 places on a panel surface note2 10 times each places at 1 sec interval dust (operation) sample dust: no. 15 (by jis-z8901) 15 seconds stir 8 times repeat at 1 hour interval no display malfunctions note1 vibration (non operation) 5 to 100hz, 19.6m/s 2 1 minute/cycle x, y, z direction 120 times each directions mechanical shock (non operation) 539m/ s 2 , 11ms x, y, z direction 5 times each directions no display malfunctions no physical damages note1 note1: display and appearance are checked under environmental conditions equivalent to the inspection conditions of defect criteria. note2: see the following fi gure for discharge points. { { { { { { { { { www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 30 6. precautions 6.1 meaning of caution signs the following caution signs have very important meaning. be sure to read "6.2 cautions" and "6.3 attentions", after understanding these contents! ! this sign has the meaning that customer will be injured by himself or the product will sustain a damage, if customer has wrong operations. this sign has the meaning that customer will get an electrical shock, if customer has wrong operations. this sign has the meaning that customer will be injured by himself, if customer has wrong operations. 6.2 cautions ? do not touch the working backlight. there is a danger of an electric shock. ? do not touch the working backlight . there is a danger of burn injury. ? do not shock and press the lcd panel and the backlight! there is a danger of breaking, because they are made of glass. (shock: to be not greater 539m/s 2 and to be not greater 11ms, pressure: to be not greater 19.6n ( 16mm jig)) 6.3 attentions 6.3.1 handling of the product take hold of both ends without touching the circuit board when the product (lcd module) is picked up from inner packing box to avoid broken down or misadjustment, because of stress to mounting parts on the circuit board. do not hook nor pull cables such as lamp cable, and so on, in order to avoid any damage. when the product is put on the table temporar ily, display surface must be placed downward. when handling the product, take the measures of electrostatic discharge with such as earth band, ionic shower and so on, because the product may be damaged by electrostatic. the torque for product mounting screws must never exceed 0.294n ? m. higher torque might result in distortion of the bezel. the product must be installed using mounting holes without undue stress such as bends or twist (see outline drawings). and do not add undue stress to any portion (such as bezel flat area). bends or twist described above and undue stress to any portion may cause display mura. do not press or rub on the sensitive product surf ace. when cleaning the product surface, use of the cloth with ethanolic liquid such as screen cleaner for lcd is recommended. do not push nor pull the interface connec tors while the product is working. ! www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 31 do not bend or unbend the lamp cable at the near part of the lamp holding rubber, to avoid the damage for high voltage side of the lamp. properly connect the plug (backlight side) to adaptable socket (inverter side) without incomplete connection. after connecting, be careful not to hook the lamp cables because incomplete connection may occur by hooking the lamp cables. this incomplete connection may cause abnormal operation of high voltage circuit. ? if the lamp cable is attached on the metal part of the product directly, high frequency leak current to the metal part may occur, then the brightness ma y decrease or the lamp may not be turned on. ? when handling the product, use of an original prot ection sheet on the product surface (polarizer) is recommended for protection of product surface. ad hesive type protection sheet may change color or characteristics of the polarizer. ? usually liquid crystals don't leak through the breakage of glasses because of the surface tension of thin layer and the construction of lcd panel. but, if you contact with liquid crystal for the worst, please wash it out with soap. 6.3.2 environment do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases. keep the product in packing box with antistatic pouch in room temperature to avoid dusts and sunlight, when storing the product. in order to prevent dew condensation occurring by temperature difference, the product packing box should be opened after enough time being left under the environment of an unpacking room. evaluate the leaving time sufficiently because a si tuation of dew condensation occurring is changed by the environmental temperature and humidity. (recommended leaving time: 6 hours or more with packing state) do not operate in high magnetic field. circuit boards may be broken down by it. this product is not designed as radiation hardened. 6.3.3 characteristics the following items are ne ither defects nor failures. characteristics of the lcd (such as response time, luminance, color uniformity and so on) may be changed depending on ambient temperature. if the product is stored under condition of low temperature for a long time, it may cause display mura . in this case, the product should be operated after enough time being left under condition of operating temperature. display mura, flicker, vertical seam or small spot may be observed depending on display patterns. optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change depending on operating time, and especially low temperature, because th e lcd has cold cathode fluorescent lamps. do not display the fixed pattern for a long time because it ma y cause image sticking. use a screen saver, if the fixed pattern is displayed on the screen. the display color may be changed depending on viewing angle because of the use of condenser sheet in the backlight. optical characteristics may be changed depending on input signal timings. the interference noise between input signal frequency for this product's signal processing board and luminance control frequency of the inverter may appear on a display. set up luminance control frequency of the inverter so that th e interference noise does not appear. after the product is stored under condition of low temperature or dark place for a long time, the cold cathode fluorescent lamp may not be turned on under the same condition because of the general characteristic of cold cathode fluorescent lamp. in addition, when luminance control ratio is low in pulse width modulation method inverter, the lamp may not be turned on. in this case, power should be supplied again. www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 32 6.3.4 other all gnd and vcc terminals should be used without any non- connected lines. do not disassemble a product or adjust variable resistors. see "replacement manual for lamp holder set", when replacing backlight lamps. pay attention not to insert foreign materials inside of the product, when using tapping screws. pack the product with original shipping package, in order to avoid any damages during transportation, when returning the product to nec for repair and so on. www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 33 7. outline drawings 7.1 front view unit: mm note1: the values in pare ntheses are for reference. note2: the torque for product mounting screws must never exceed 0.294n ? m. note3: mounting hole portions (4 pieces) www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 34 7.2 rear view unit: mm note1: the values in pare ntheses are for reference. note2: the torque for product mounting screws must never exceed 0.294n ? m. note3: mounting hole portions (4 pieces) www.datasheet.co.kr datasheet pdf - http://www..net/
NL8060BC26-30D preliminary data sheet dod-pp-0394 (3rd edition) 35 revision history the inside of latest specifications is revised to th e clerical error and the ma jor improvement of previous edition. only a changed part such as functions, characteristic value and so on that may affect a design of customers, are described especially below. edition document number prepared date revision contents and signature 1st edition dod-pp- 0346 aug 3, 2007 revision contents new issue 2nd edition dod-pp- 0383 sep. 28, 2007 revision contents p1 module name, p5 structure and principle, p34 outline drawings-rear view: ? nl8060bc26-30 NL8060BC26-30D (change) p6 general specifications ? polarizer surface: clear antiglare (change) 3rd edition dod-pp- 0394 oct. 11, 2007 revision contents p6 general specifications ? weight: (475) g (typ.) ? color gamut: 60% (typ.) 40% (typ.) p8 mechanical specifications ? weight: (475) g (typ.) p27 optical characteristics ? color gamut: 55% (min.), 60% (typ.) 35% (min.), 40% (typ.) t. ogawa checked by writer t. ogawa approved by prepared by m. tanaka checked by signature of writer t. ogawa approved by prepared by m. tanaka checked by writer t. ogawa approved by prepared by www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of NL8060BC26-30D

	To Download NL8060BC26-30D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .